diff --git a/include/configs/tt01.h b/include/configs/tt01.h
new file mode 100644
index 0000000..6ef25cd
--- /dev/null
+++ b/include/configs/tt01.h
@@ -0,0 +1,254 @@
+/*
+ * (C) Copyright 2011 HALE electronic <helmut.raiger@hale.at>
+ * (C) Copyright 2008 Magnus Lilja <lilja.magnus@gmail.com>
+ *
+ * Configuration settings for the HALE TT-01 board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include <asm/arch/imx-regs.h>
+
+/* High Level Configuration Options */
+#define CONFIG_ARM1136
+#define CONFIG_MX31
+#define CONFIG_MX31_HCLK_FREQ	26000000
+#define CONFIG_MX31_CLK32	32768
+
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DISPLAY_BOARDINFO
+
+#define CONFIG_CMDLINE_TAG		/* enable passing of ATAGs */
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_MACH_TYPE	3726		/* not yet in mach-types.h */
+#define CONFIG_SYS_TEXT_BASE	0xA0000000
+
+
+/*
+ * Physical Memory Map:
+ *   CS settings are defined by i.MX31:
+ *     - CSD0 and CDS1 are 256MB each, starting at 0x80000000 and 0x9000000
+ *     - CS0 and CS1 are 128MB each, at A0000000 and A8000000
+ *     - CS2 to CS5 are 32MB each, at B0.., B2.., B4.., B6..
+ *
+ * HALE set-up of the bluetechnix board for now is:
+ *   - 128MB DDR (2x64MB, 2x16bit), connected to 32bit DDR ram interface
+ *   - NOR-Flash (Spansion 32MB MCP, Flash+16MB PSRAM), 16bit interface at CS0
+ *		- S71WS256ND0BFWYM (and CS1 for 64MB S71WS512ND0 without PSRAM)
+ *        the flash chip is a mirrorbit S29WS256N !
+ *   - the PSRAM is hooked to CS5 (0xB6000000)
+ *   - Intel Strata Flash PF48F2000P0ZB00, 16bit interface at (CS0 or) CS1
+ *     - 64Mbit = 8MByte (will go away in the production set-up)
+ *   - NAND-Flash NAND01GR3B2BZA6 at NAND-FC:
+ *		1Gbit=128MB, 2048+64 bytes/page, 64pages x 1024 blocks
+ *   - Ethernet controller SMC9118 at CS4 via FPGA, 16bit interface
+ *
+ * u-boot will support the 32MB nor flash and the 128MB NAND flash, the PSRAM
+ * is not used right now. We should be able to reduce the SOM to NAND flash
+ * only and boot from there.
+ */
+#define CONFIG_NR_DRAM_BANKS	1
+#define PHYS_SDRAM_1		CSD0_BASE
+#define PHYS_SDRAM_1_SIZE	(128 * 1024 * 1024)
+
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_LATE_INIT
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+#define CONFIG_SYS_GBL_DATA_OFFSET \
+	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR	\
+	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
+
+/* default load address, 1MB up the road */
+#define CONFIG_SYS_LOAD_ADDR		(PHYS_SDRAM_1+0x100000)
+
+/* The stack sizes are set up in start.S using the settings below */
+#define CONFIG_STACKSIZE	(128 * 1024)	/* regular stack */
+
+/* Size of malloc() pool, make sure possible frame buffer fits */
+#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 10*1024*1024)
+
+/* memtest works on all but the last 1MB (u-boot) and malloc area  */
+#define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM_1
+#define CONFIG_SYS_MEMTEST_END \
+	(PHYS_SDRAM_1+(PHYS_SDRAM_1_SIZE-CONFIG_SYS_MALLOC_LEN-0x100000))
+
+/* CFI FLASH driver setup */
+#define CONFIG_SYS_FLASH_CFI		/* Flash memory is CFI compliant */
+#define CONFIG_FLASH_CFI_DRIVER		/* Use drivers/cfi_flash.c */
+#define CONFIG_FLASH_SPANSION_S29WS_N
+/*
+ * TODO: Bluetechnix (the supplier of the SOM) did define these values
+ * in their original version of u-boot (1.2 or so). This should be
+ * reviewed.
+ *
+ * #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+ * #define CONFIG_SYS_FLASH_PROTECTION
+ */
+#define CONFIG_SYS_FLASH_BASE		CS0_BASE
+#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT (254+8) /* max number of sectors per chip */
+
+/*
+ * FLASH and environment organization, only the Spansion chip is supported:
+ * - it has 254 * 128kB + 8 * 32kB blocks
+ * - this setup uses 4*32k+3*128k as monitor space = 0xA000 0000 to 0xA00F FFFF
+ *		and 2 sectors with 128k as environment =
+ *		A010 0000 to 0xA011 FFFF and 0xA012 0000 to 0xA013 FFFF
+ * - this could be less, but this is only for developer versions of the board
+ *   and no-one is going to use the NOR flash anyway.
+ *
+ * Monitor is at the beginning of the NOR-Flash, 1MB reserved. Again this is
+ * way to large, but it avoids ENV overwrite (when updating u-boot) in case
+ * size breaks the next boundary (as it has with 128k).
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN		(1024 * 1024)
+
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE	(128 * 1024)
+#define CONFIG_ENV_SIZE		(8 * 1024) /* smaller for faster access */
+
+/* Address and size of Redundant Environment Sector	*/
+#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
+
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+
+/* Hardware drivers */
+
+/*
+ * on TT-01 UART1 pins are used by Audio, so we use UART2
+ * TT-01 implements a hardware that turns off components depending on
+ * the power level. In PL=1 the RS232 transceiver is usually off,
+ * make sure that the transceiver is enabled during PL=1 for testing!
+ */
+#define CONFIG_MXC_UART
+#define CONFIG_SYS_MX31_UART2
+
+#define CONFIG_MXC_SPI
+#define CONFIG_MXC_GPIO
+
+/* MC13783 connected to CSPI3 and SS0 */
+#define CONFIG_PMIC
+#define CONFIG_PMIC_SPI
+#define CONFIG_PMIC_FSL
+
+#define CONFIG_FSL_PMIC_BUS		2
+#define CONFIG_FSL_PMIC_CS		0
+#define CONFIG_FSL_PMIC_CLK		1000000
+#define CONFIG_FSL_PMIC_MODE	(SPI_MODE_0 | SPI_CS_HIGH)
+#define CONFIG_FSL_PMIC_BITLEN	32
+
+#define CONFIG_RTC_MC13XXX
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+/* console is UART2 on TT-01 */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_BAUDRATE			115200
+#define CONFIG_SYS_BAUDRATE_TABLE	{9600, 19200, 38400, 57600, 115200}
+
+/* ethernet setup for the onboard smc9118 */
+#define CONFIG_MII
+#define CONFIG_SMC911X
+/* 16 bit, onboard ethernet, decoded via MACH-MX0 FPGA at 0x84200000 */
+#define CONFIG_SMC911X_BASE		(CS4_BASE+0x200000)
+#define CONFIG_SMC911X_16_BIT
+
+/*
+ * Command definition
+ */
+
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_SAVEENV
+#define CONFIG_CMD_NAND
+/*
+ * #define CONFIG_CMD_NAND_LOCK_UNLOCK the NAND01... chip does not support
+ * the NAND_CMD_LOCK_STATUS command, however the NFC of i.MX31 supports
+ * a software locking scheme.
+ */
+
+#define CONFIG_BOOTDELAY	3
+
+/*
+ * currently a default setting for booting via script is implemented
+ *   set user to login name and serverip to tftp host, define your
+ *   boot behaviour in bootscript.loginname
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS \
+	"bootcmd=dhcp bootscript.$(user); source\0"
+
+#define CONFIG_BOOTP_SERVERIP /* tftp serverip not overruled by dhcp server */
+#define CONFIG_BOOTP_SEND_HOSTNAME /* if env-var 'hostname' is set, send it */
+
+/* Miscellaneous configurable options */
+#define CONFIG_HUSH_PARSER
+#define CONFIG_PROMPT_HUSH_PS2	"> "
+
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_PROMPT	"TT01> "
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+/* Print Buffer Size */
+#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE + \
+				sizeof(CONFIG_SYS_PROMPT)+16)
+/* max number of command args */
+#define CONFIG_SYS_MAXARGS	16
+/* Boot Argument Buffer Size */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_HZ			1000
+
+#define CONFIG_CMDLINE_EDITING
+
+#define CONFIG_NAND_MXC
+#define CONFIG_SYS_MAX_NAND_DEVICE		1
+#define CONFIG_SYS_NAND_MAX_CHIPS		1
+
+/*
+ * actually this is nothing someone wants to configure!
+ * CONFIG_SYS_NAND_BASE despite being passed to board_nand_init()
+ * is not used by the driver.
+ */
+#define CONFIG_MXC_NAND_REGS_BASE	NFC_BASE_ADDR
+#define CONFIG_SYS_NAND_BASE		NFC_BASE_ADDR
+#define CONFIG_MXC_NAND_HWECC
+
+/* the current u-boot driver does not use the nand flash setup! */
+#define CONFIG_SYS_NAND_LARGEPAGE
+/*
+ * it's not 16 bit:
+ * #define CONFIG_SYS_NAND_BUSWIDTH_16BIT
+ *    the current u-boot mxc_nand.c tries to auto-detect, but this only
+ *    reads the boot settings during reset (which might be wrong)
+ */
+
+#endif /* __CONFIG_H */